Fusion Test Equipment

From Grid to Magnet

Test equipment for every stage of a fusion facility's power systems

Isometric diagram of a fusion facility's power path, linked by cables: a transmission pylon, a flywheel generator with a capacitor bank and converter cubicles, high-voltage switchgear and a converter transformer, a neutral beam injector with radio-frequency sources and their supply cabinets, and a generic tokamak with its field coils
What we test here

Click a pin or a stage to see what gets tested there, and with what.

Cinergia GE Series four-quadrant grid emulator
Cinergia
GE+ Series
Regenerative AC/DC grid emulator up to 160 kW, with voltage dips, harmonics and frequency changes
Pacific Power Source AZX Series regenerative AC and DC power source
Pacific Power Source
AZX Series
Silicon-carbide regenerative source, DC to 1000 Hz, single, split or three phase
Yokogawa WT5000 precision power analyser
Yokogawa
WT5000
Up to seven input elements for converter efficiency and loss measurement, ±0.03% basic power accuracy
Yokogawa WT1800R high-performance power analyser
Yokogawa
WT1800R
Harmonic analysis to the 500th order on up to six elements, ±0.05% power accuracy
Elektro-Automatik EA PSB 10000 bidirectional DC supply
Elektro-Automatik
EA PSB 10000
30 kW DC supply that also sinks power and returns it to the mains, models up to 2000 V and 1000 A
Elektro-Automatik ELR 21000 30kW High Speed regenerative DC electronic load
Elektro-Automatik
EA-ELR 21000 30kW High Speed
Fast-slewing regenerative DC load with 125% overpower for 500 ms and up to 95% energy recovery
Elektro-Automatik EA-ELR 10000 4U regenerative DC electronic load
Elektro-Automatik
EA-ELR 10000 4U
Programmable DC load that feeds up to 96% of absorbed power back to the mains, with CV, CC, CP and CR modes
Associated Research Hypot Series production hipot tester
Associated Research
Hypot Series
Production hipot and insulation resistance testing to 5 kV AC or 6 kV DC, with stored results
Associated Research OMNIA II electrical safety compliance analyser
Associated Research
OMNIA II
Hipot, insulation resistance, ground bond, continuity and leakage current in one analyser
Associated Research HypotULTRA hipot, insulation resistance and ground bond tester
Associated Research
HypotULTRA
4-in-1 dielectric analyser in 2U, with touchscreen and storage for 100,000 results
CAEN ELS FAST-PS Series bipolar digital power supply
CAEN ELS
FAST-PS Series
Bipolar digital supply with true zero-crossing and 10 kHz update rates over SFP
CAEN ELS FAST-Bi-1K5 Series bipolar bidirectional power supply
CAEN ELS
FAST-Bi-1K5 Series
1.5 kW four-quadrant bipolar supply, regenerative, designed for duties including superconducting magnet control
CAEN ELS EASY-DRIVER Series bipolar current supply
CAEN ELS
EASY-DRIVER Series
Compact 1U bipolar current supplies from ±1 A to ±10 A, with Ethernet control
Kepco BOP four-quadrant bipolar power supply
Kepco
BOP
Four-quadrant bipolar supply and amplifier, 40 W to 5 kW, for inductive and capacitive loads
CAEN ELS NGPS Series high-stability digital power supply
CAEN ELS
NGPS Series
High-stability 10 kW digital DC supply, temperature coefficient under 1 ppm/°C, parallels to 40 kW
CAEN ELS FAST-PSM Series monopolar digital power supply
CAEN ELS
FAST-PSM Series
Monopolar 600 W digital supply with 10 kHz SFP updates, for magnet power applications

Beyond the diagram

Calibration, rental and help with your test set-up

A fusion test programme can run for years, so the instruments on a rig are likely to come due for calibration more than once. We calibrate power analysers, DC supplies, loads and electrical safety testers in our own laboratory, rent sources and loads for test campaigns, and can support you in choosing an appropriate set-up for a new rig.

What testing do fusion power systems need?

From the grid connection to the magnets, almost every system in a fusion facility converts, stores or switches power. The equipment is usually tested at several points: on prototypes and model coils in R&D, at the supplier's works in production, and at factory and site acceptance before it is connected to the machine. What sets fusion apart is the duty: short pulses at very high power, inductive loads that store a lot of energy, and control circuits that reverse current cleanly through zero.

In the UK, UK Fusion Energy is building STEP Fusion, a prototype plant at West Burton in the East Midlands that it aims to have operational in 2040, with a design intended to deliver net power to the grid. The government has committed £2.5 billion to fusion energy, of which £1.3 billion funds the next stage of STEP Fusion. For UK suppliers of power conversion, magnet, heating and high-voltage equipment, that is likely to mean more qualification and acceptance testing in the years ahead.

Caltest's calibration laboratory is UKAS accredited (No. 4432). UKAS-accredited calibration is available on products covered by our Schedule of Accreditation; other instruments receive a traceable calibration certificate. If you use high-current DC supplies for magnet work, ask us which ranges we can cover before you plan a recalibration. Tell us what your applications are, with ratings and test durations, and we can support you in choosing an appropriate configuration, whether you buy, rent or need existing equipment calibrated.

Read more: where fusion fits in the nuclear test and calibration chain →